Whatman filter

Important!! The following is a text only archive!
For full features; Go to Whatman filter

posted by TomSizeMore

is it absolutely necessary to cook the oil before running it through the filter?

posted by Smallguy

you need to heat the oil to help with then disovling process... also warmer oil is easier to push through a whatman

so say you do not have to bake the final product I always do.

posted by regino007

I have always added the oil to the product while in hot water but never cooked it unless I was making water based winny in peg400.I like the way it flows through the filter when its warm.

posted by batfink0

The only reason you apply heat is for the reason Small Guy states. Heating or baking your oil DOES NOT sterilze it. Anything over 260 degrees can harm the hormone. I usally bake it for 10 secs, to heat up the poweder so it can be mixed with the BB and BA. Then i will bake it at 225 twice..for about 10 mins each time, and give it a good shake in between and after!....To make sure the hormones dissolve and spread evenly through the oil.

My fav...is injecting my prods while their still warm....LOL....I guess some women feel this when they eat their baking right out of the oven....

I'm such a Betty Crocker!

P.S.

Smallguy blows goats.....LOL...how did I know I'd find you on this forum...

posted by TomSizeMore

I'm just wanting to use the oil to thin out another batch that I already have. Am I going to have to worry about heating it?

posted by batfink0

No.....but consider this....Oil is NOT sterilized unless its been through a whatman filter .02. I guess that's why you called this thread whatman filter....lol
Go ahead. I've done it before with pre-made Orbit products. They tend to put like 5-7% BA in their prods. Facking kicks the shite out of me for days!
Go ahead and cut it down. If you need help re-calculating what your dosages should be, or the strength of your newly diluted junk, don't be afraid to PM me. :)

posted by TomSizeMore

Cool, I appreciate it. I'm just going to add 10ml to 10ml and that way i'll know for sure what the dosage is.

Thanks again,

posted by regino007

I totally disagree with this.The only way a product is sterlized is with the use of BA not a filter.The filter is used as a product to "filter" out any unwanted stuff in a finished product.

posted by TomSizeMore

U think this could be why I can't walk right now? I injected into my right quad two days ago and I can't even bend my leg.

posted by batfink0

The reason I didn't mention this, is because he is already adding it to a BA enriched product. But yes....obviously you need Ba to kill of everything... The oil itself needs to be filtered though.

As for your leg.....lol...
How much experience do you have with injecting.....What are you injecting..and how much...Also....whats the lab of your product?

posted by regino007

I under stood your post as saying if you run any type of fliud throught a Watman it will sterilize that fliud.

posted by TomSizeMore

I've got experience, but your gonna laugh when I tell you what I injected. I shot 100ml test P 100ml tren Ace and 100ml Test suspension. in a 3ml plunger. I still can't walk right. It's been a full 3 days. No discoloration though, just horrible soreness. It's all UG stuff.

posted by batfink0

well then..that explains it...LOL....and you must mean 100mg...however..those numbers seem low.....

Are you saying that your prop, tren and Susp, are all 100mg/ml?
Or is this after you diluted them with your additional oil?

I personally don't do 3ml shots...Fack...that makes me gringe even thinking about it!.....lol

posted by CUTS

batfink, those your boobies?

posted by batfink0

If i had those...I wouldn't have time to write this.....I'd be too busy tweaking and flicking....lol

posted by CUTS

hahaha flicking!

posted by TomSizeMore

First of all, I like the boobies. Tweaking and flicking is fun

My prop/tren is a blend at 100mg/ml each ML. the suspension is 50mg/ml and I put two ML in the syringe.

* Add Your Comment - Ask a question *
Share the knowledge!

+
+
+
+
+
+ ...

+
+
------
+
+
+
------
+
+
+
+